Yealink SIP-T46G User Manual

Browse online or download User Manual for Corded Phones Yealink SIP-T46G. Yealink SIP-T46G User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 2
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
Accessing the web user interface:
Account Settings: Click on Account->Register->Account X (X=1,2,3,4,5,6)
Parameters of the account:
Network Settings:
Account Settings:
Configuring via phone user interface
Configuring via web user interface
Configuring Your Phone
Register status icons on the LCD screen:
Quick Installation Guide
www.yealink.com
Note: Check with your system administrator if any error appears during the registration process or a specific
configuration is required for your registration.
Note: The wrong network settings may result in the inaccessibility of your phone and may have an impact on the
network performance. Contact your system administrator for more information.
1. Press the OK key when the phone is idle to obtain the IP address of the phone.
You can configure the network settings in the following ways:
It shows the register status of the current account.
You can select Enabled/Disabled to enable/disable the account.
It is shown on the LCD to identify the account.
It is shown as caller ID when placing a call.
It is provided by ITSP for registration (required).
It is an authenticated ID for authentication provided by ITSP (required).
It is provided by ITSP for registration (required).
It is provided by ITSP for registration (required).
DHCP: By default, the phone attempts to contact a DHCP server in your network to obtain its valid
network settings, e.g., IP address, subnet mask, gateway address and DNS address.
Static IP Address: If your phone can not contact a DHCP server for any reason, you need to
configure the IP address, subnet mask, gateway address, primary DNS address and
secondary DNS address for the phone manually.
PPPoE: If you are using an xDSL modem, you can connect your phone to the Internet via PPPoE
mode. Contact the ITSP for the account and password.
Press the Menu soft key when the phone is idle, select Advanced (password: admin)->Network->
WAN Port/VLAN/Webserver Type/802.1x Settings/VPN to configure the network.
For more information, refer to the User Guide available online:
http://www.yealink.com/SupportDownloadfiles_detail.aspx?CateId=310&flag=142
Press the Menu soft key when the phone is idle, select Advanced (password: admin)->Account to
configure the account.
2. Open the web browser on your computer, enter the IP address into the address bar (e.g.,
"http://192.168.0.10" or "192.168.0.10") and then press the Enter key.
Register Status:
Line Active:
Label:
Display Name:
User Name:
Register Name:
Password:
Server Host:
3. Enter the user name (default: admin) and password (default: admin) in the login page
and click Confirm.
Network Settings: Click on Network->Basic->IPv4 Config
Registered
Register Failed
Registering
Copyright 2014 YEALINK NETWORK TECHNOLOGY CO.,LTD.
c
SIP-T46G
Ultra-elegant Gigabit IP Phone
Applies to firmware version 72.1 or later.
Note: For more information on account parameters, refer to Configuring via web user interface.
(Gray)
(Green)
(Yellow)
(V72.4)
Page view 0
1 2

Summary of Contents

Page 1 - SIP-T46G

Accessing the web user interface:Account Settings: Click on Account->Register->Account X (X=1,2,3,4,5,6)Parameters of the account:Network Setti

Page 2 - Assembling the Phone

Startup1. Attach the stand, as shown below:2. Connect the handset and optional headset, as shown below:3. Connect the network and power, as shown belo

Comments to this Manuals

No comments